Autostart Two-way Led Automatic Transmission Remote Starter Manual de usuario descargar pdf (Pagina 3)

Tach Programming

Flash the hood pin (see on page 1)

— the parking lights will stay on for up to 20 seconds.

Before the lights go out, press and hold the brake pedal and press the

lock

and

unlock

buttons simultaneously — the

parking lights will flash 4 times At that point, release the brake pedal.

Start up the engine and allow the vehicle to reach regular engine idle speed.

Once the engine is running idle, press the brake pedal and keep it down until you hear the parking lights output click

5 times.

Release the brake pedal —^the tach programming is now complete.

Horn Honk Timing

Follow these steps to program horn confirmation:

1. Ensure that the hood is up and that the ignition is off.

• Hold the hood pin down for 4 seconds.

• Release the hood pin. The parking lights will come on.

• While the parking lights are on, immediately push and release the hood pin again. ^— The parking lights will stay on for up to

20 seconds.

2. Press and hold the brake pedal, then simultaneously press the

unlock

and

start

buttons — the horn will chirp 5 times.

3. Release the brake pedal.

4. To change the timing:

1. To increase the Horn pulse by 3 ms, press the

LOCK

button.

2. To decrease the pulse by 3 ms, press the

unlock

button.

3. To increase the pulse by 10 ms, press the

start

stop

button.

4. To decrease the pulse by 10 ms, press the

trunk

button.

5. To save the new settings: press

LOCK

and

unlock

. If 3 chirps are returned the new settings have been saved.

Supplementary Information

Fifth Relay Output

(2nd IGN, ACC or CRANK)

Remote car starters of this series are equipped with an on-board

high-current programmable 5

relay that can be used to power a

second ignition, accessory or crank wire. The unit uses 3 sets of

pins; each set corresponds to a specific function of the output. In

order to activate one of the three possible functions, you must place

the jumper (supplied) on one of the three sets of pins and connect

the 14 AWG wire to the second

IGN. / ACC. / CRANK

wire of the

vehicle.

Caution!

Only one set of pins can be used at one time. Using more than one jumper may result in

serious damage to the vehicle. The relay output rating on this unit is 25 a at most. Defective

oem solenoid switches can sometimes draw up to 50 or 60 a, causing the 30 a fuse to

blow. Always verify your circuit with an appropriate measuring device.

Tach jumper settings

Some new vehicles have a higher TACH voltage threshold,

which would fall out of the normal TACH trigger circuit of the

remote car starter. Changing the jumper to TACH Threshold

HIGH will allow the module to properly detect the TACH signal.

http://www.autostart.ca

Installation Guide

FUNCTION 2 - Engine Run Time

OPTION 1

Run Time = 3 minutes in

gas

mode / 8 minutes

diesel

mode

OPTION 2*

Run Time = 15 minutes in gas mode / 20 minutes diesel mode

OPTION 3

Run Time = 25 minutes in

gas

mode / 30 minutes

diesel

mode

FUNCTION 3 - Idle/Turbo Mode

OPTION 1

Idle mode

disabled

/ turbo mode

disabled

OPTION 2*

Idle mode enabled / turbo mode enabled

FUNCTION 4 - Engine type and Cold Weather Mode

OPTION 1

Diesel mode with 20-minute run time in cold weather mode (30-sec. delay)

OPTION 2*

Gas mode with 3-minute run time in cold weather mode

OPTION 3

Diesel mode with 8-minute run time in cold weather mode (18-sec. delay)

OPTION 4

Diesel mode with 8-minute run time in cold weather mode (7-sec. delay)

FUNCTION 5 - Ignition Valet

OPTION 1 Ignition valet

disabled

OPTION 2* Ignition valet enabled

mode 3 *

INDICATES DEFAULT SETTING

FUNCTION 1 - Home Valet

OPTION 1 Home valet

enabled

OPTION 2*

Home valet disabled

FUNCTION 2 - aux 1 Programming

OPTION 1 Horn confirmation upon the 2

press of the

LOCK

button.

OPTION 2*

Priority door access

OPTION 3 Horn confirmation upon the 1

press of the

lock

button.

FUNCTION 3 - aux 2 Programming

OPTION 1 Constant output by pressing

SHIFT

then maintaining the

LOCK

button pressed.

In safe start mode: activate

AUX 2

by pressing the

START/ STOP

button.

OPTION 2*

Toggle ON/OFF (with 30-second timeout)

OPTION 3 Toggle

ON/OFF

(with 4 minutes timeout) ^active when under remote run

OPTION 4 Priority door access

FUNCTION 4 - aux 3 / Zone 3 Programming

OPTION 1 1-sec. output when

trunk

button is pressed for 3 sec. with ignition off or under remote run

OPTION 2*

Constant output while the trunk button is pressed

OPTION 3 Output with disarm and rearm pulses when pressing the

trunk

button

FUNCTION 5 - External Trigger

OPTION 1

Zone 3 disarm/rearm (trunk pin: a disarm pulse is sent before the trunk opens, the vehicle

rearms 4 seconds after the trunk is closed).

OPTION 2*

Engine start/stop

OPTION 3

Key sense

OPTION 4 Domelight supervision (Smart ignition lock at the press of the brakes)

OPTION 5 Pager

MODE 4 * INDICATES DEFAULT SETTING

function 1 - Multi-Level Features

OPTION 1 Multi-car features, Basic features, Customized features

option 2* Basic features, Multi-car features, Customized features

OPTION 3 Customized features, Multi-car features, Basic features

OPTION 4 Basic features, customized features, Multi-car features

Installation Guide

http://www.autostart.ca/

P. 6 P. 3

1 2 3 4

Comentarios a estos manuales

Sin comentarios

Autostart Two-way Led Automatic Transmission Remote Starter Manual de usuario Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Autostart Two-way Led Automatic Transmission Remote Starter